Water Butt Diverter Kit fits both Round and Square Downpipes packed by Buttacup

Product Information

If you’re eco-conscious, consider what the water butt is made from. Designs produced in the UK from high-density recycled plastic tend to feel stronger and more robust , while also being kinder to the environment.

If you don’t mind splurging on a water butt because you want to add to the visual appeal of your garden, and are happy to spend a little more purchasing all of the extras (the filler kit and the stand), then I would say it’s worth it. However, if you’re on a tighter budget and prioritise function over form, then there are other water butts out there that provide better value for money. Drainage Superstore is proud to offer a range of rainwater diverters from brands such as Lindab, Brett Martin, Hargreaves and Alumasc, to work with your roofline drainage system. Choose from a number of different styles to fit in with your current rainwater system, and rest assured that whichever product you choose will not only perform well but also be of the highest quality. First, work out how often you’ll be using your water butt. If you plan on filling a watering can a few times a week, then a 100 litre water butt would probably suffice, considering that the average watering can holds 10 litres. These water butts also usually have slimmer designs that take up less space.

Fitting the Water Butt

Your plants will certainly thank you for installing a butt, as rainwater is much better for plants than tap water. A water butt can be fitted to any downpipe where there is space to sit a container either directly underneath or nearby. They are easy and cheap to fit and can be an attractive feature in the garden. Choosing a Water Butt The design of a watering can can mean that much of the water doesn’t reach the roots where it is most needed, so be careful with this Using a rainwater diverter is a great way to save on utility bills, reduce your impact on the environment, and keep a store of free and clean water for use in your home and garden. Save money

If space isn’t too much of an issue, water butts of between 250 – 300 litres are standard size. They’re the best water butts for most domestic small/medium gardens. Water resources in the UK are under pressure from climate change and population growth. Gardeners should therefore use mains water as sparingly as they can. Drill a hole in the side of the water butt, 8cm down from the top. The hole needs to be just the right size to fit the connector fitting of the diverter through. Fit the connector piece in place by pushing it through the hole you just drilled and screwing the supplied washer and nut on. It’s easy to see why this water butt appeals to such a wide range of people. It’s sleek enough to sit inconspicuously in the corner of small gardens, yet it’s also slim enough to be lined up in a row of connected water butts to contribute to a larger water storage system. It’s one of the best water butts if you’re after a slimline design. Fit the rubberised splash seal to the top section of pipe, then connect the diverter between the two sections. Make sure that the outlet hole is at the bottom. Then pull the splash seal down over the join.First flush filters divert and flush the first water which enters the system when the rain starts pouring. This is because this first water is always the most contaminated by leaves, dust and other materials on the roof. One design feature that I particularly appreciated was the child-safe, spring-loaded fastening clip on the lid . Some of the other water butts that I tested required a screwdriver to open the lid, so the fact that you can peek inside this one without any tools required is a bonus. Also, unlike the other water butts that I reviewed, where the downfill pipe attached into the side of the water butt, this one connects via its lid . This is unusual, but neither good nor bad.

You can install a water butt next to the down pipe of your house or any garden building that has a system of gutters, such as a shed, greenhouse, conservatory or outdoor office. If the structure does not have the necessary pipe work, it might be worth adding them to help you save water. How to install a water butt In rainwater harvesting systems water flows from the roof down a downpipe (drainpipe) to the water butt , where it is stored. Diverters are the pipes used to connect the downpipe to the water butt. The most basic are used to divert water only only, whilst others also filter the water they divert. Plants need the most water in hot, dry and windy weather, which is usually when water companies are least able to meet demand. Plants are most vulnerable to shortages of water when they are first planted when their roots have not yet established into the deeper, moister layers of soil. Newly planted shrubs, trees, herbaceous perennials, seedlings, annuals and vegetables will all need watering to be managed carefully until their roots establish. Once plants have established, keeping your soil healthy by adding organic matter should help to minimise the need for watering. But what is a rainwater diverter, how do they work, and why should you use a rainwater diverter? Read on to find out more about rainwater diverters, and if you have any questions, don’t hesitate to call our team on 01752 692221 or use the live chat in the bottom right hand corner, and they will be more than happy to help.

See also...

Follow the instructions supplied with the butt to ensure your model is installed in the correct way. Generally, there are two main ways of fitting a water butt in your garden. You can remove the lower part of a down pipe, so the upper part runs directly into a butt placed beneath it, adding an overflow pipe to take excess water away to the drain.